A/C PERFORMANCE

The A/C system is designed to provide the passenger compartment with low temperature and low humidity air. The A/C evaporator, located in the HVAC housing is cooled to temperatures near the freezing point. As warm damp air passes over the fins of the A/C evaporator, the air transfers its heat to the refrigerant in the evaporator coils and the moisture in the air condenses on the evaporator fins. During periods of high heat and humidity, an A/C system will be more effective in the Recirculation mode (max-A/C). With the system in the Recirculation mode, only air from the passenger compartment passes through the A/C evaporator. As the passenger compartment air dehumidifies, the A/C system performance levels rise.

Humidity has an important bearing on the temperature of the air delivered to the interior of the vehicle. It is important to understand the effect that humidity has on the performance of the A/C system. When humidity is high, the A/C evaporator has to perform a double duty. It must lower the air temperature, and it must lower the temperature of the moisture in the air that condenses on the evaporator fins. Condensing the moisture in the air transfers heat energy into the evaporator fins and coils. This reduces the amount of heat the A/C evaporator can absorb from the air. High humidity greatly reduces the ability of the A/C evaporator to lower the temperature of the air.

However, evaporator capacity used to reduce the amount of moisture in the air is not wasted. Wringing some of the moisture out of the air entering the vehicle adds to the comfort of the passengers. Although, an owner may expect too much from their A/C system on humid days. A performance test is the best way to determine whether the system is performing up to design standards. This test also provides valuable clues as to the possible cause of trouble with the A/C system. The ambient air temperature in the location where the vehicle will be tested must be a minimum of 21° C (70° F) for this test.


A/C PERFORMANCE TEST

WARNING: Refer to the applicable warnings and cautions for this system before performing the following operation (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - WARNING) and (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - CAUTION). Failure to follow the warnings and cautions could result in possible personal injury or death.

NOTE: When connecting the service equipment coupling to the line fitting, verify that the valve of the coupling is fully closed. This will reduce the amount of effort required to make the connection.

NOTE: The work area ambient temperature and the evaporator temperature must be above 18.3°C (65°F) prior to conducting the A/C Performance Test.


STEP 2STEP 2

  • Engine at 1,000 rpm at operating temperature
  • Doors and windows closed
  • Transmission in Park
  • A/C-heater controls set to Recirculation mode (max-A/C), full cool, panel mode, high blower and with A/C compressor engaged. If the A/C compressor does not engage, see the A/C System Diagnosis chart.



A/C PERFORMANCE TEMPERATURE AND PRESSURE

Ambient Air Temperature
 
21°C
(70°F)
 
27°C
(80°F)
 
32°C
(90°F)
 
38°C
(100°F)
 
43°C
(110°F)
 
Maximum Allowable Air Temperature at Center Panel Outlet
 
9°C
(48°F)
 
9°C
(48°F)
 
12°C
(54°F)
 
15°C
(59°F)
 
18°C
(65°F)
 
Suction Pressure at Service Port (Low Side)
 
138 to 207 kPa
(20 to 30 psi)
 
138 to 207 kPa
(20 to 30 psi)
 
207 to 276 kPa
(30 to 40 psi)
 
207 to 276 kPa
(30 to 40 psi)
 
241 to 310 kPa
(35 to 45 psi)
 
Discharge Pressure at Service Port (High Side)
 
1034 to 1724 kPa
(150 to 250 psi)
 
1379 to 2068 kPa
(200 to 300 psi)
 
1551 to 2241 kPa
(225 to 325 psi)
 
1724 to 2413 kPa
(250 to 350 psi)
 
2068 to 2758 kPa
(300 to 400 psi)
 



A/C SYSTEM DIAGNOSIS

Condition
 
Possible Causes
 
Correction
 
Rapid A/C compressor clutch cycling (ten or more cycles per minute).
 

Very low refrigerant system charge.

 

See Refrigerant System Leaks in this group. Test the refrigerant system for leaks. Repair, evacuate and charge the refrigerant system, if required.

 
Equal pressures, but the compressor clutch does not engage.
 

1. No refrigerant in the refrigerant system.

 

1. See Refrigerant System Leaks in this group. Test the refrigerant system for leaks. Repair, evacuate and charge the refrigerant system, if required.

 

2. Open fuse.

 

2. Check the fuses in the Power distribution block and junction block. Repair the shorted circuit or component and replace the fuses, if required. Refer to Group 8.

 
 

3. Inoperative A/C compressor clutch coil.

 

3. See A/C Compressor Clutch Coil in this group. Test the compressor clutch coil and replace, if required.

 
 

4. Inoperative A/C compressor clutch relay.

 

4. See A/C Compressor Clutch Relay in this group. Test the compressor clutch relay and relay circuits. Repair the circuits or replace the relay, if required.

 
 

5. Improperly installed or inoperative evaporator temperature sensor.

 

5. See Evaporator Temperature Sensor in this group. Test the sensor and replace, if required.

 
 

6. Inoperative A/C pressure transducer.

 

6. See A/C Pressure Transducer in this group. Test the sensor and replace, if required.

 
 

7. Inoperative Powertrain Control Module (PCM) or Engine Control Module (ECM).

 

7. Refer to Group 9 - Engine Electrical Diagnostics for testing of the PCM/ECM. Test the PCM/ECM and replace, if required.

 
 
Normal pressures, but A/C Performance Test air temperatures at center panel outlet are too high.
 

1. Excessive refrigerant oil in system.

 

1. See Refrigerant Oil Level in this group. Recover the refrigerant from the refrigerant system and inspect the refrigerant oil content. Restore the refrigerant oil to the proper level, if required.

 

2. Blend door actuator (s) improperly installed or inoperative.

 

2. See Blend Door Actuator in this group. Inspect the actuator(s) for proper operation and replace, if required.

 
 

3. Blend-air door(s) inoperative or sealing improperly.

 

3. See HVAC Housing in this group. Inspect the blend-air door(s) for proper operation and sealing. Repair if required.

 
 
The low side pressure is normal or slightly low, and the high side pressure is too low.
 

1. Low refrigerant system charge.

 

1. See Refrigerant System Leaks in this group. Test the refrigerant system for leaks. Repair, evacuate and charge the refrigerant system, if required.

 

2. Refrigerant flow through the A/C evaporator is restricted.

 

2. See A/C Evaporator in this group. Replace the restricted A/C evaporator, if required.

 
 

3. Inoperative A/C compressor.

 

3. See A/C Compressor in this group. Replace the A/C compressor, if required.

 
 
The low side pressure is normal or slightly high, and the high side pressure is too high.
 

1. A/C condenser air flow restricted.

 

1. Check the A/C condenser for damaged fins, foreign objects obstructing air flow through the condenser fins, and missing or improperly installed air seals. Clean, repair, or replace components as required.

 

2. Refrigerant flow through the A/C receiver/drier is restricted.

 

2. See A/C Receiver/Drier in this group. Replace the restricted receiver/drier, if required.

 
 

3. Inoperative radiator cooling fan.

 

3. Test the radiator cooling fan and replace, if required. Refer to Group 7 - Cooling.

 
 

4. Refrigerant system overcharged.

 

4. See Refrigerant System Charge in this group. Recover the refrigerant from the refrigerant system. Charge the refrigerant system to the proper level, if required.

 
 

5. Air in the refrigerant system.

 

5. See Refrigerant System Leaks in this group. Test the refrigerant system for leaks. Repair, evacuate and charge the refrigerant system, if required.

 
 

6. Engine overheating.

 

6. Test the engine cooling system and repair, if required. Refer to Group 7 - Cooling.

 
 
The low side pressure is too high, and the high side pressure is too low.
 

1. Accessory drive belt slipping.

 

1. Inspect the accessory drive belt condition and tension. Repair as required. Refer to Group 7 - Cooling.

 

2. Inoperative A/C expansion valve.

 

2. See A/C Expansion Valve in this group. Replace the valve, if required.

 
 

3. Inoperative A/C compressor.

 

3. See A/C Compressor in this group. Replace the A/C compressor, if required.

 
 
The low side pressure is too low, and the high side pressure is too high.
 

1. Restricted refrigerant flow through the refrigerant lines.

 

1. See Liquid Line, Suction Line and Discharge Line in this group. Inspect the refrigerant lines for kinks, tight bends or improper routing. Correct the routing or replace the refrigerant line, if required.

 

2. Restricted refrigerant flow through the A/C expansion valve.

 

2. See A/C Expansion Valve in this group. Replace the valve, if required.

 
 

3. Restricted refrigerant flow through the A/C condenser.

 

3. See A/C Condenser in this group. Replace the restricted A/C condenser, if required.