B1D10(DDM), B1D19(PDM) – MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT HIGH





For a complete wiring diagram Refer to Section 8W.


  • When Monitored:

    Continuously

  • Set Condition:

    The (P65) Driver Mirror Horizontal Position Signal circuit supplies input to the Driver Door Module. DTC B1D10 will set if the input value is greater than the known good (stored) value for more than 60 ms.

    The (P68) Passenger Mirror Horizontal Position Signal circuit supplies input to the Passenger Door Module. DTC B1D19 will set if the input value is greater than the known good (stored) value for more than 60 ms.


Possible Causes
 
FOR THE DRIVER MEMORY MIRROR SYSTEM:
 
(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO VOLTAGE
 
(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT OPEN
 
(P69) DRIVER MIRROR SENSOR GROUND CIRCUIT OPEN
 
DRIVER OUTSIDE REARVIEW MIRROR SHORTED
 
DRIVER DOOR MODULE
 
FOR THE PASSENGER MEMORY MIRROR SYSTEM:
 
(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO VOLTAGE
 
(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT OPEN
 
(P66) PASSENGER MIRROR SENSOR GROUND CIRCUIT OPEN
 
PASSENGER OUTSIDE REARVIEW MIRROR SHORTED
 
PASSENGER DOOR MODULE
 


NOTE: This procedure addresses the Driver Memory Mirror system's circuits and components and the Passenger Memory Mirror system's circuits and components. Select only that which applies to the system you are diagnosing.



Diagnostic Test

1.TEST FOR INTERMITTENT CONDITION








Does the scan tool display: B1D10 or B1D19 MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT HIGH?

Yes
  • Go To 2


No

2.TEST FOR A SHORTED OUTSIDE REARVIEW MIRROR



For the Driver Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Driver Outside Rearview Mirror connector.
  • Connect a voltmeter between the (P65) Driver Mirror Horizontal Position Signal circuit and the (P69) Driver Mirror Sensor Ground circuit.
  • Turn the ignition on.
  • Move the mirror switch to any switch position while monitoring the voltmeter.

For the Passenger Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Passenger Outside Rearview Mirror connector.
  • Connect a voltmeter between the (P68) Passenger Mirror Horizontal Position Signal circuit and the (P66) Passenger Mirror Sensor Ground circuit
  • Turn the ignition on.
  • Move the mirror switch to any switch position while monitoring the voltmeter.


What is the voltage?

4.8 to 5.2 Volts


Above 5.2 Volts
  • Go To 3


Below 4.8 Volts
  • Go To 4

3.CHECK THE (P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT OR THE (P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE



For the Driver Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Driver Door Module C2 connector.
  • Turn the ignition on.
  • Measure the voltage of the (P65) Driver Mirror Horizontal Position Signal circuit.

For the Passenger Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Passenger Door Module connector.
  • Turn the ignition on.
  • Measure the voltage of the (P68) Passenger Mirror Horizontal Position Signal circuit.


Is the voltage above 0.2 volts?

Yes, Driver Mirror


Yes, Passenger Mirror


No, Driver Mirror


No, Passenger Mirror

4.CHECK THE (P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT OR THE (P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT FOR AN OPEN



For the Driver Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Driver Door Module C2 connector.
  • Measure the resistance of the (P65) Driver Mirror Horizontal Position Signal circuit between the Driver Outside Rearview Mirror connector and the Driver Door Module C2 connector.

For the Passenger Memory Mirror System, proceed as follows:
  • Turn the ignition off.
  • Disconnect the Passenger Door Module connector.
  • Measure the resistance of the (P68) Passenger Mirror Horizontal Position Signal circuit between the Passenger Outside Rearview Mirror connector and the Passenger Door Module C2 connector.


Is the resistance below 2.0 ohms?

Yes
  • Go To 5


No, Driver Mirror


No, Passenger Mirror

5.CHECK THE (P69) DRIVER MIRROR SENSOR GROUND CIRCUIT OR (P66) PASSENGER MIRROR SENSOR GROUND CIRCUIT FOR AN OPEN



For the Driver Memory Mirror System, proceed as follows:
  • Measure the resistance of the (P69) Driver Mirror Sensor Ground circuit between the Driver Outside Rearview Mirror connector and the Driver Door Module C2 connector.

For the Passenger Memory Mirror System, proceed as follows:
  • Measure the resistance of the (P66) Passenger Mirror Sensor Ground circuit between the Passenger Outside Rearview Mirror connector and the Passenger Door Module C2 connector.


Is the resistance below 2.0 ohms?

Yes, Driver Mirror


Yes, Passenger Mirror


No, Driver Mirror


No, Passenger Mirror