CLUTCH SYSTEM

Clutch problem diagnosis will generally require a road test to determine the type of fault. Component inspection will then determine the problem after road testing.

Drive the vehicle at normal speeds during road test. Shift the transaxle through all gear ranges and observe clutch action. If chatter, grab, slip, or improper release is experienced, remove and inspect the clutch components. If the problem is noise or hard shifting, further diagnosis may be needed. The transaxle or other driveline components may actually be at fault.


CLUTCH GRAB/CHATTER

CONDITION
 
POSSIBLE CAUSES
 
CORRECTION
 
CLUTCH DISC FACING COVERED WITH OIL OR GREASE
 
Oil leak at engine rear main or transaxle input shaft seal.
 
T355 equipped- Correct leak and replace modular clutch assembly.
 
BG6 equipped - Clean pressure plate, flywheel, and replace clutch disc.
 
   
Too much grease applied to splines of disc and input shaft.
 
Apply lighter coating of grease to splines.
 
 
NO FAULT FOUND WITH CLUTCH
COMPONENTS
 
Problem actually related to suspension or driveline component.
 
Further diagnosis required. Check engine/transmission mounts, suspension attaching parts and other driveline components as needed.
 
Engine related problems.
 
Check EFI and ignition systems.
 
 
PARTIAL ENGAGEMENT OF CLUTCH DISC
 
Clutch cover, spring, or release fingers bent, distorted (rough handling, improper assembly).
 
Replace clutch assembly.
 
Clutch disc damaged or distorted.
 
Replace clutch assembly.
 
 
Clutch misalignment.
 
T355 equipped - Verify modular clutch pilot plate alignment to crankshaft. Replace the modular clutch assembly if the pilot plate is loose or bent.
 
 
BG6 equipped - Check alignment and runout of flywheel, disc, or cover. Check clutch housing to engine dowels and dowel holes for damage. Correct as necessary.
 
   


CLUTCH SLIPS

CONDITION
 
POSSIBLE CAUSES
 
CORRECTION
 
DISC FACING WORN OUT
 
Normal wear.
 
Replace clutch assembly.
 
Driver frequently rides (slips) clutch, results in rapid wear, overheating.
 
Replace clutch assembly.
 
 
Insufficient clutch cover diaphragm spring tension
 
Replace clutch assembly.
 
 
CLUTCH DISC FACING CONTAMINATED WITH OIL OR GREASE
 
Leak at rear main oil seal or transaxle input shaft seal
 
T355 equipped - Replace leaking seals. Replace clutch assembly.
 
BG6 equipped - Replace leaking seals. Clean the pressure plate and flywheel surface and replace clutch disc.
 
   
Excessive amount of grease applied to input shaft splines
 
T355 equipped - Apply less grease to input shaft. Replace clutch assembly.
 
 
BG6 equipped - Apply less grease to input shaft. Clean the pressure plate and flywheel surface and replace clutch disc.
 
   
Road splash, water entering housing
 
Seal housing. Inspect clutch assembly.
 
 
Concentric Slave Cylinder leaking hydraulic fluid
 
Replace Concentric Slave Cylinder (CSC)
 
 
CLUTCH IS RUNNING PARTIALLY DISENGAGED
 
Release bearing sticking or binding, does not return to normal running position.
 
Verify that bearing is actually binding. Then, replace bearing and transmission front bearing retainer if sleeve surface is damaged.
 
Slave cylinder binding
 
Replace slave cylinder
 
 
CLUTCH DISC FACINGS HAVE FRACTURED INTO SMALL PIECES
 
Driver performs a 5-1 downshift at vehicle speed in excess of 60 miles per hour
 
Alert driver to problem cause. Replace clutch assembly. Inspect slave cylinder and bearing for damage.
 
Leak at rear main or transaxle input shaft seal
 
T355 equipped - Replace seal. Replace clutch assembly.
 
 
BG6 equipped - Replace seal. Clean the pressure plate and flywheel surface and replace clutch disc.
 
   
Excessive heat from slippage
 
Replace Clutch Assembly
 
 


IMPROPER CLUTCH RELEASE

CONDITION
 
POSSIBLE CAUSES
 
CORRECTION
 
CLUTCH DISC BINDS ON INPUT SHAFT SPLINES
 
Clutch disc hub splines damaged during installation
 
Clean, smooth, and lubricate disc and shaft splines. Replace modular clutch assembly, or clutch disc, and/or input shaft if splines are severely damaged.
 
Input shaft splines rough, damaged.
 
Clean input shaft splines. Then lube.
 
 
Corrosion or rust formations on splines of input shaft and disc
 
Clean input shaft splines and disc splines, then lube
 
 
CLUTCH DISC RUSTED TO FLYWHEEL AND/OR PRESSURE PLATE
 
Occurs in vehicles stored or not driven for extended period of time. Also occurs after steam cleaning if vehicle is not used for extended period.
 
Replace clutch assembly.
 
CLUTCH WILL NOT DISENGAGE PROPERLY
 
Disc bent, distorted during transaxle installation
 
Replace clutch assembly.
 
Clutch cover diaphragm spring damaged during transaxle installation
 
Replace clutch assembly.
 
 
Air in clutch hydraulic system.
 
Bleed clutch hydraulic system to purge air.
 
 
Clutch master cylinder or slave cylinder leaking
 
Check and replace master and/or slave cylinder
 
 


CLUTCH PEDAL NOISE

CONDITION
 
POSSIBLE CAUSES
 
CORRECTION
 
CLUTCH PEDAL SQUEAKS WHEN DEPRESSED TO FLOOR
 
Pedal bushings worn out or inadequate lubrication
 
Replace or lubricate bushings
 
Clutch pedal return spring worn out
 
Lubricate or replace return spring